I purchased a Crucial SSD and used the included Apricorn software and cable. Process could not have been easier. Instructions are very easy to understand. Entire process from start to finish was a snap; took about 25 minutes. Popped in the ssd and I was off to the races. Thank You Apricorn. (Posted on 4/18/13)

I don't normally write reviews, but I was in a bad spot with my hard drive and needed to get all of my data and OS over to a new one quickly. I had tried EZ gig III but had not had any success. EZ gig IV did the work flawlessly.

One word of caution: on the first step of the cloning process, it got to 99% done in about a minute then stayed at 99% for a WHILE. Don't give up, I just went to sleep and in the morning, everything was done. (Posted on 4/14/13)

I agree with the general consensus here that this product really works! I too tried many other cloning solutions but either their interface was too clunky and most likely written by geeks for geeks and / or the cloned drive never booted. This is all history. This product clones anything to anything. Most of my cloned drives are smaller size SSDs than their cloned counterparts and this product has no issues in doing what it has to do to get the job completed. And it does it fast too: With the USB 2 interface it can clone a 100GB OS drive in less than an hour. (Posted on 4/7/13)

It is a powerful and useful product but it will not boot with HP computers such as dc7800 and 6200. (Posted on 3/30/13)

Copied my Intel 80GB SSD boot drive onto a Crucial m4 256GB SSD using this software. It was very easy to use, no gimmicks or fluff, and did exactly what I needed it to do. The data transfer went off without any problem at all, and the new M4 drive worked immediately after installation. I thought the disk swap process was going to be a difficult and long drawn out process, and I had been putting it off for as long as possible until I bought the M4 (which came with the EZ Gig IV Cloning Software). The Gig IV cloning software and Crucial's excellent 256GB M4 made the upgrade quick, pleasant and straightforward. (Posted on 3/24/13)

I cloned my 7200 rpm hard disk, in my IMB-Lenovo Z61p laptop, to an Intel X-25M 160 GB SSD. I then just swapped them and rebooted without any problems, just like before BUT much faster. The Apricorn EZ Gig III (or now IV) SATA Wire kit, is a very affordable, easy and reliable product. I can't imagine a better and more convenient product than this, thanks a lot for this product!! (Posted on 3/4/13)

Have some old "IDE" hard drives (<1GB) that won't recognize, but all the recent stuff works fine. (Posted on 2/8/13)

Finally, a cloning product that does what it says it will. No if's and's or buts. Previously I tried ALL of the most popular cloning software out there to no avail. Either there was some problem while booting from the recovery media, or you had to purchase the more expensive "plus" version to get a nice GUI boot menu to allow the copy process to proceed. After cloning, probably 80% of the time the disk would not boot (particularly on my Dell).

Your product worked perfectly the first time w/o any hiccups. I am a happy camper :-) (Posted on 1/27/13)

Got this when I bought a Crucial SSD. It works perfectly IF you have the matching size SSD or HD to replace the current one. (Posted on 1/21/13)

Cloned my new hard drive and swapped drives after it finished, I started using my laptop with the cloned drive right away without any problems. Very satisfied. (Posted on 1/16/13)

Easy to use.
Worked perfect to clone win 8 (Posted on 1/8/13)

Cloned my drive as easy as 1-2-3. Thanks for a great product. (Posted on 12/16/12)

Cloning was fast and precise. I purchased the EZ Gig II and could not get it to clone my drive, came to the site used EZ Gig IV and within a few minutes my hard dirve was cloned. (Posted on 3/24/12)

The product is very good and useful for copying and moving data files from one hard drive to another hard drive on pc and laptop. (Posted on 3/13/12)

My elderly mothers' hard drive decided to stop working, so I came to the rescue (so I thought). After wasting two entire days and the better part of a third, I decided to visit my neighborhood electronics store and see if I might get some advice from one of their techies, but before anyone came to my assistance, I happened across this little gem... Apricorn’s "Notebook Hard Drive Upgrade Kit". Included in the kit are an exceptionally nice hard drive enclosure, a USB to mini-USB cable, and their "EZ Gig III for Windows" software, along with a suite of other software products designed especially for cloning. This product, in addition to some sound advice from Brandon at Apricorn, resulted in a rewarding experience replacing my first-ever hard drive. I didn't have to reload the operating system, any software, or any data. I couldn't be more pleased (and my mother was quite excited, too). Thank you!
(Posted on 9/13/11)

I purchased the Drive Wire kit from Microcenter. It came with EZ-Gig III. I was upgrading a 160GB 4200RPM HD on my Compaq laptop. I had read in another review that the HP & Compaq didn't like some earlier versions of EZ-Gig so I downloaded EZ-Gig IV from your sight. I ran it right from windows and it cloned to a 500GB 7200RPM Seagate flawlessly in about 55 minutes; no read or write erros. I took my old drive out & put the new one in and it booted right up as if nothing had changed. Now I just have way more space on a much faster drive. I thought about manually adjusting the partitions using the software right before cloning but thought I would just give it a go on the automatic setting. Like I said, it worked great. The only thing I would change is that the recovery partion went from 10GB on the old drive to 30GB on the new drive which is really bigger than I need but otherwise, perfect. Thanks for the Great Product!
(Posted on 8/5/11)